METHOD of application of Gator Stone Bond XP for a NEW PAVER JOB:
INSTALLATION INSTRUCTIONS:

• AGGREGATE SELECTION FOR FINAL SURFACE: Select an aggregate that contains a variety of sizes. For instance, crushed stone mixes such as 3/8 minus, 1/4 minus or 3/16 minus work well with Gator Stone Bond XP, where as single size aggregates like 3/8 rock or pea gravel are not suitable. Screenings with extremely high fine content are not suitable either. To ensure compatibility of selected aggregate with Gator Stone Bond XP, prepare a test area.
• STRUCTURAL STONE BASE PREPARATION: Before starting the actual project, factors such as climate, native soil type, amount of use, should be taken into consideration. As a rule of thumb, “The better the base preparation, the better the results.”

Option 1 – For optimum performance, install 4 to 6 in. of 3/4 minus crushed stone, then compact using a vibratory plate compactor.

Option 2 – Install 2 to 4 in. of 3/4 minus or 3/8 minus, 1/4 minus or 3/16 minus, then compact using a vibratory plate compactor. In restricted areas where a compactor will not fit, use a hand tamper.

1. SURFACE AGGREGATE: Spread a minimum of 1” surface aggregate over the compacted structural stone base. Rake or screed to the desired level, a minimum slope of 2 degrees to allow water run off. Do not compact until after Gator Stone Bond XP has been applied.
2. APPLY THE GATOR STONE BOND XP: Using a watering can or pump sprayer, apply the Gator Stone Bond XP to the surface at the rate of 15 sq. ft. (1.4 sp. m.) per gallon for residential pedestrian use, or 10 sq. ft. (0.9 sq. m.) per gallon for commercial pedestrian use. Allow Gator Stone Bond XP to fully penetrate through the material
3. COMPACTION: While surface is still damp but not saturated, compact the surface with a vibratory plate compactor; 2 or 3 passes are recommended. In restricted areas where a compactor will not fit, use a hand tamper. The better the compaction, the better the results.

Instructions for rebuilding AN EXISTING SURFACE:

1. Scarify or rototill at least 1 inch of the surface, break up any clumps, making any necessary repairs, and add new surface aggregate as needed.
2. Apply Gator Stone Bond XP at the rate of15 sq. ft. (1.9 to 4.1 sp. m.) per gallon; allow liquid to penetrate.
3. Compact using a vibratory plate compactor. In restricted areas where a compactor will not fit, use a hand tamper.

Instructions for maintaining AN EXISTING SURFACE:

1. Make repairs as needed.
2. Apply Gator Stone Bond XP at the rate of 20 to 45 sq. ft. (1.4 sp. m.) per gallon. Some judgement will be needed, as consideration for absorption and desired results should be taken into account.
3. Compact any loose areas.

IMPORTANT INFORMATION

1. Gator Stone Bond XP is not a sealer, and we do not recommend using it as such.
2. Where the vibratory plate will not reach, use a hand tamper or a block of wood and a hammer, compact corners and other hard to reach areas.
3. All crushed stone aggregates are not created equal, when in doubt, do a test area.
4. Gator Stone Bond XP does work on sands, but sands are not considered as strong “structurally speaking” as a crushed stone mix with larger size stones like a 3/8 minus would have.
5. Gator Stone Bond XP may slightly darken the crushed stone mix.
6. Gator Stone Bond XP is not concrete, expect that some surface aggregates will become loose over time.
7. In some instances a crack may appear, (to fix, see instructions on maintaing an existing surface).
8. Slope the surface with a minimum of 2 degrees, so water will run off.
9. Form or taper the edges (if you choose to form, leave them in place when done).
10. Allow 24 to 48 hours at a temperature above 59°F (15°C) for surface to cure.
11. Do not apply Gator Stone Bond XP if rain is expected within 48 hours.
12. Please store Gator Stone Bond XP container at above 32°F (0°C)